Appliance Error Codes
Admiral
Error Code | Condition | Check/Repair |
---|---|---|
F0 | Jammed Function Key | Replace the touch pad or the entire clock if the pad is not separate from the clock. |
F1 | Defective Clock or Touch Pad | Replace the touch pad or replace the clock. |
F2 | Temperature of oven is too hot | Inspect the sensor harness. Get a new oven temperature sensor or relay board. |
F3 | Short in Oven Temperature Sensor | Inspect both the sensor harness and the wiring that runs from the oven control and sensor. Get a new oven sensor if there is nothing wrong with the sensor. |
F4 | Short in Oven Temperature Sensor | Inspect both the sensor harness and the wiring that runs from the oven control and sensor. Get a new oven sensor if there is nothing wrong with the sensor. |
F5 | Hardware Conflict | Install a new clock. |
F7 | Jammed/Short Function Key | Install a new touch pad or new clock. |
F8 | Analog/Digital Malfunction | Swap out the clock. |
F9 | Door Latch Malfunction | Look at the latch on the door. Fix or replace as necessary. |
Amana
Error Codes for Amana Range/Stove/Oven Fault Codes
Error Codes for Amana Range/Stove/Oven Fault Codes
AMANA - Dual Convection Wall OvenAMANA - Big Oven 5.1 Cubic Foot (Sigma Touchmatic Electronic Range Control)
Failure Code - Glass Link Electronic Range Control (ERC) | Condition | Check/Repair |
---|---|---|
Flashing 0, 1, 2, or 3 on Door | Latch Switch is Broken | Install new latch switch. |
Flashing Lock | Latch Switch is Broken | Install new latch switch. |
F0 | Lost Safety Signal | Install new adapter board. |
F1 | Watchdog Circuit | Install new ERC |
F2 | Oven Getting Too Hot | Install a new oven temperature sensor |
F3 | Short in Temperature Sensor | Install a new sensor. |
F4 | Temperature Sensor Short | Install a new sensor. |
F7 | Touch Panel Short | Install a new glass panel. |
F9 | Door Motorized | Look at the latch switch. Repair or replace. |
FF | Lock Malfunction | Look at the motor and the switch. Repair or replace. |
ERC III/Relay Board With Separate Board/Push Buttons | Condition | Check/Repair |
F0 | Short in Push Pad | Replace faulty pad |
F1 | ECR Failure | Install a new ECR |
F2 | Oven Temperature Too High | Replace faulty temperature sensor |
F3 | Short in Oven Temperature Sensor | Install new temperature sensor. |
F4 | Short in Oven Temperature Sensor | Install new temperature sensor. |
F5 | ECR Malfunction | Install new ECR. |
F6 | ECR Malfunction | Install new ECR. |
F7 | Button Sticking | Inspect alignment of glass. Install a new touch panel. |
F8 | ECR Malfunction | Install new ECR. |
F9 | Faulty Door Latch | Install a new latch or door assembly. |
ERC III/Relay Board With Separate Board/Push Buttons | Condition | Check/Repair |
F0 | Short in Touch Pad | Install a new touch pad. |
F1 | ECR Failure | Install a new ECR. |
F2 | Oven More Than 100 Degrees Too Hot | Install a new ECR. |
F3 | Short in Oven Sensor | Install a new ECR. |
F4 | Short in Oven Sensor | Install a new ECR. |
F6 | ECR Component Malfunction | Install new ECR. |
F6 | ECR Malfunction | Install a new ECR. |
F7 | Self-Clean Lock Circuitry Malfunction | Inspect the mechanism of the door latch. |
ERC III/Relay Board With Separate Board/Push Buttons | Condition | Check/Repair |
F0-0 | Initial factory setting. | No Error |
F1-1 | Cooking Temperature Higher Than Setting | Inspect oven temperature sensor and wiring. Replace sensor/wiring if malfunctioning. Replace ERC if the wiring and sensor are working properly. |
F1-3 | Cleaning Temperature Higher Than Setting | Inspect oven temperature sensor and wiring. Replace sensor/wiring if malfunctioning. Replace ERC if the wiring and sensor are working properly. |
F1-5 | Input for Revoke Key Out of Range | Install a new control board. |
F1-7 | Short in Key | Install a new control board. |
F1-8 | Malfunction in Slave Micro | Install a new control board. |
F1-9 | Grounding Circuit Board Malfunction | Install a new control board. |
F1-A | Control Not Calibrated | Install a new control board. |
F1-C | Circuit Board Data Corrupted | Install a new control board. |
F1-F | Circuit Board Data Corrupted | Install a new control board. |
F1-H | Malfunction in Door Switch Input Circuit | Look at the door switch and the wiring. Repair or replace. |
F1-J | Malfunction in Door Switch Input Circuit | Look at the door switch and the wiring. Repair or replace. |
F3-1 | Oven Temperature Sensor or Sensor Circuit Malfunction | Look at the oven temperature sensor and wiring. Repair or replace. |
F9-1 | Locking Failure of Auto Latch | Look at the latch switch, motor and wiring. Repair or replace. |
F9-2 | Auto Latch Fails to Unlock | Look at the latch switch, motor and wiring. Repair or replace. |
ASKO
ASKO - Dishwasher
Error Code | Condition | Check/Repair |
---|---|---|
F-1 | Water Not Heating to Desired Temperature in an Hour | • Incoming water cold • Heating element burned out • Thermostat malfunction |
F-2 | Water Level High | • Plugged or water pump • Malfunctioning water pump • Defective water inlet valve |
F-3 | Faulty Thermostat | • Open thermostat • Poor thermostat wiring |
F-4 | Water Fill Fault on Machines With Level-Controlled Fill (Dead Controls, Blinking Lights and a Running Pump) | Disconnect power. Take off lower access panels. Get rid of water in he tray below the dishwasher. Verify the pump functions properly. Test dishwasher. Inspect the drain hose below the sink. It should flow to the underside of the countertop and then down the drain. |
ASKO - Dryer
Error Code | Condition | Check/Repair |
---|---|---|
F1 | Condensate Drain Too Full | Check the drain tube and condensate reservoir pump. |
F2 | Maximum Drying Time Exceeded By Three Hours or Longer | Check the circuit breaker, fuses, duct work, hi-limit thermostat, cycling thermostat, and heating element. Replace blown fuses and remove lint. |
F3 | Thermistor Fault | Inspect thermistor wiring. Install new wiring or a new thermistor. |
F4 | Lint Build Up in Lint Filter, Condenser or Front Housing | Remove lint. |
F5 | Moisture Sensor Malfunction | Remove lint. Check wiring. Replace sensor. |
ASKO - Washing Machine
Error Code | Condition | Check/Repair |
---|---|---|
F1 | Lower Water Fill | Check water supply and install a new water inlet valve. |
F2 | Water Level Too High | Check water pump for blockage. Replace pump or valve. |
F3 | Pump Malfunction | Clean pump trap. |
F4 | Thermistor Problem | Check wiring. Install new thermistor. |
F6 | Motor Malfunction | Check wiring connecting to the motor. Replace motor. |
F7 | Malfunctioning Door Lock | Check door latch. Replace solenoid. |
00 00 | Machine Not Spinning | Redistribute load and restart machine. |
CALORIC
CALORIC - Range/Stove/Oven Fault Codes
Error Code | Condition | Check/Repair |
---|---|---|
Door Flashing 0, 1, 2, 3 | Latch Switch Malfunction | Replace switch. |
"Lock" Flashing | Latch Switch Malfunction | Replace switch. |
F0 | No Safety Signal | Install new adapter board. |
F1 | Watchdog Circuit Problem | Install new Electronic Range Control (ERC) |
F2 | Oven Overheats | Install new temperature sensor. |
F3 | Short in Oven Temperature Sensor | Install new temperature sensor |
F4 | Short in Oven Temperature Sensor | Install new temperature sensor |
F7 | Short in Touch Panel | Install a new touch panel. |
F9 | Motorized Door Issue | Check door latch. |
FF | Door Lock Malfunction | Check latch motor and door switch. |
CALORIC - ERC III/Relay Board With Separate Board/Push Buttons
Error Code | Condition | Check/Repair |
---|---|---|
F0 | Short in Touch Pad | Install a new pad |
F1 | ECR Failure | Install a new ECR |
F2 | Oven Temperature Too High | Replace faulty temperature sensor |
F3 | Short in Oven Temperature Sensor | Install a new temperature sensor. |
F4 | Short in Oven Temperature Sensor | Install a new temperature sensor. |
F5 | ECR Malfunction | Install new ECR. |
F6 | ECR Malfunction | Install new ECR. |
F7 | Button Sticking | Inspect alignment of glass touch panel. Replace. |
F8 | ECR Malfunction | Install new ECR. |
F9 | Door Latch Malfunction | Install a new latch. |
CALORIC - RST376 Gas Range Fault/Error Codes
Error Code | Condition | Check/Repair |
---|---|---|
F1 | Malfunctioning Clock | Install new clock assembly. |
F2 | Malfunctioning Oven Temperature Sensor | Install a new sensor. |
F3 | Open Oven Temperature Sensor | Install a new sensor. |
F4 | Low Rating Oven Sensor | Install a new oven temperature sensor. |
F5 | Clock Malfunction | Install a new clock assembly. |
F6 | Power Surge | Turn power off for 60 seconds. Turn back on. Install a new clock assembly if necessary. |
F7 | Sticking Touch Panel Button | Install a new touch panel. |
F8 | Diagnostic Read Out Malfunction | Install a new clock assembly. |
DACOR
DACOR - Range/Stove/Oven Fault Codes
Error Code | Condition | Check/Repair |
---|---|---|
F0 | Jammed Clock Button | Check button. |
F1 | Element Relay Circuit Malfunction | Install a new control board. |
F2 | Oven Temperature Higher Than the Clean Runaway Temp in Self-Clean Mode or The Cooking Runaway Temp in Cooking Mode | Schedule professional repair. |
F3 | Short in Oven Temperature Circuit | Inspect sensor. If there is no resistance, install a new sensor. |
F4 | Short in Oven Temperature Circuit | Inspect sensor. If there is no resistance, install a new sensor. |
F6 | FEEPROM Check Comparison Malfunction | Schedule a service call or install a new clock control. |
F7 | Malfunction in Self-Clean Automatic Door Latch System | Check the door latch and the switches. |
F8 | Door Latch Motor Malfunction | Check the door latch and the lock motor. |
ESTATE
ESTATE - Range/Stove/Oven Fault/Error Codes
Error Code | Condition | Check/Repair |
---|---|---|
F0 | Board Malfunction | Install a new control board and clock. |
F1 | Board Malfunction | Install a new control board and clock. |
F2 | Oven Overheating | Install a new oven control and clock if the welded relay contact has broil relays. Inspect door lock if a self-clean model. Look for causes of high resistance. |
F3 | Oven Temp Sensor Open | Get new sensor. |
F4 | Short in Temp Sensor | Get new sensor. |
F5 | Board Malfunction | Install a new control board. |
F7 | Function Key Jam | Install a new control board. |
ESTATE - Range/Stove/Oven Fault/Error Codes
Error Code | Condition | Check/Repair |
---|---|---|
F0 | Board Malfunction | Install a new control board. |
F1 | Board Malfunction | Install a new control board. |
F2 | Oven Temp Higher Than Recommended | For self-clean models, inspect door lock operations. For models with baked relays on the welded relay contacts, get a new over control. Check sensor and connections for high resistance. |
F3 | Open Oven Temp Sensor | Install a new sensor. |
F4 | Oven Temp Sensor Short | Install a new sensor. |
F5 | Board Malfunction | Install a new control board. |
F7 | Function Key Jam | Install a new control board. |
FRIGIDAIRE
FRIGIDAIRE - Range/Stove/Oven Fault Codes Version 1
Error Code | Condition | Check/Repair |
---|---|---|
F2 | Temperature of Oven Higher Than Specifications | Indicates oven temp is higher than 965 degrees Fahrenheit with the door locked or higher than 665 degrees with door unlocked. |
F3 | Open Oven Temperature Sensor | Inspect open wire connection that runs from the electronic over control clock and oven temp sensor. Install a new sensor. |
F4 | Oven Temperature Sensor Short | Inspect open wire connection that runs from the electronic over control clock and oven temp sensor. Install a new sensor. |
F5 | Watchdog On Instead of Off | Check the electronic oven control relay after choosing the clean operation. |
F6 | Lack of 60 Hz Time Base | Install a new electronic oven control. |
F7 | Watchdog On Instead of Off | Check the electronic oven control relay after choosing the clean operation. |
F8 | Watchdog On Instead of Off | Check the electronic oven control relay after choosing the clean operation. |
GE
GE - Gas or Built In Oven Fault Codes
Error Code | Condition | Check/Repair |
---|---|---|
F0 | Transistor Malfunction | Try to delete code. Get a new touch pad or electronic range control if necessary. |
F1 | Transistor Malfunction | Try to delete code. Get a new touch pad or electronic range control if necessary. |
F2 | Oven Temperature Reaches More Than 590 degrees F With Unlocked Door or More Than 990 F With Locked Door | Check for welded relay contacts or high resistance connection. |
F3 | Oven Temperature Sensor Circuit Open | Inspect wire connections. Ensure that oven temperature sensor is around 100 ohms at room temperature. |
F4 | Short in Oven Temp Sensor Circuit | Look for melted connector and shorts in the leads. |
F8 | ECR Component Malfunction | Install a new ECR. |
F9 | Door Lock Circuit Issue | Check wiring and switch operation. |
GE - XL44 Self Clean Oven Fault Codes
Error Code | Condition | Check/Repair |
---|---|---|
F0 | Keypad Stuck | Press the "clear/off" button. Disconnect ribbon cable from control. Wait 32 seconds. If code reappears, get a new control. Replace the key panel if the code does not reappear. |
F1 | Keypad Stuck | Press the "clear/off" button. Disconnect ribbon cable from control. Wait 32 seconds. If code reappears, get a new control. Replace the key panel if the code does not reappear. |
F2 | Oven is Overheating in the Clean, Cooking or Operation modes, or the Oven Temp is Higher Than 650 Degrees in Locked Mode, or Airflow Issue | Inspect welded relay contacts. Check if the thermal switch is closing. Look for causes of high resistance or electrical noise interference in the oven temperature sensor circuit. |
F3 | Short in Temperature Sensor or Sensor is Over 2700 Ohms | Disconnect power. Take out temp sensor connector. Check that the sensor reads 1100 ohms at room temp. Measure oven temperature sensor that runs from the connector block to ground. Check for cut or pinched wires. Check connector terminals for rust or bends. Fix or replace. |
F4 | Short in Temperature Sensor or Sensor is Over 2700 Ohms | Disconnect power. Take out temp sensor connector. Check that the sensor reads 1100 ohms at room temp. Measure oven temperature sensor that runs from the connector block to ground. Check for cut or pinched wires. Check connector terminals for rust or bends. Fix or replace. |
F5 | Relay Safety Circuit Malfunction | Look for intermittent high resistance in the oven temperature sensor circuit. Check the lock circuit. Press "clear/off" and wait for the code to reappear. Install a new control if necessary. |
F7 | Keypad Stuck | Press the "clear/off" button. Disconnect ribbon cable from control. Wait 32 seconds. If code reappears, get a new control. Replace the key panel if the code does not reappear. |
FC | Door Lock Switch or Circuit Malfunction | Inspect wiring and switches. |
FD | Meat Probe Short | Inspect that the probe's resistance is between 30k ohms and 50k ohms at room temperature. Check for pinched wires or condensation near the installation. |
FF | Connection Loss in the Door Motor Safety Circuit | Install a new control. |